- Also called:
- mass spectroscopy
The energy of an ion is proportional to the square of its velocity, so ions of constant energy can be separated through the use of fields that vary with time. In the United States William R. Smythe first proposed such a device in 1926 based on electrodes to which radio-frequency voltages are applied and which are arranged so that ions of a given velocity pass undeflected. He built a working model a few years later in collaboration with Mattauch. The method did not prove to be particularly useful and did not see further development. Following World War II the techniques of manipulating very short electrical pulses allowed the construction of the time-of-flight mass spectrometer, in which a short emission of ions is released from the source and their arrival times recorded after having traversed a distance sufficiently long to sort out the different speeds.
In 1953 the West German physicists Wolfgang Paul and Helmut Steinwedel described the development of a quadrupole mass spectrometer. The application of superimposed radio frequency and constant potentials between four parallel rods can be shown to act as a mass separator in which only ions within a particular mass range will perform oscillations of constant amplitude and be collected at the far end of the analyzer. This device has the advantage of high transmission.
General principles
The evolution of mass spectrometry has been marked by an ever-increasing number of applications in science and technology. New applications and new developments have gone hand in hand to create a complex array of instruments, but all may be understood by tracing the ions through three basic elements: an ion source, a method of analyzing the ion beams according to their mass-to-charge ratio, and detectors capable of measuring or recording the currents of the beams. These elements exist in many forms and are combined to produce spectrometers with specialized characteristics. The needs of users vary, as do the chemical form and the amount of sample available for analysis, which may be in submicrogram quantities. The result is a great variety of design.
Ion sources
Direct-current arc
Historically this was the first way of producing a beam of ions and came quite naturally out of the 19th-century experiments for observing the passage of electricity in gases at low pressure. Two planar electrodes oriented perpendicular to the axis of the electric field can, with a few hundred-volt potential difference, form a plasma discharge. (Plasma refers to an ionized gas containing an approximately equal number of positive ions and electrons.) Electrons attracted to the anode collide with molecules of the gas to form ions and free more electrons; the positive ions contribute in turn to further ionization by their collisions. A hole in the cathode allows positive ions to emerge collimated into a beam. Such sources are found with many electrode configurations, including electron-emitting filaments, and operate with wide ranges of pressures and voltages. Sources with magnetic fields parallel to the electric fields can yield beams greater than one milliampere. Direct-current sources were widely used during the first decades of mass spectrography. They served well for gases and liquids introduced as vapours and for many solids as well, because these could be transformed into gaseous atoms and incorporated into the plasma through impact by the ions, a process called sputtering. One disadvantage of this kind of ionization is the wide band of energies attained by the ions, ranging from the maximum electrode potential to almost zero. Such a distribution of energies was the cause of Thomson’s parabolas, but accurate work requires a narrow energy range, which in this case must be achieved in the analyzer section of the instrument.
Electron bombardment
Electrons extracted from a glowing filament may be used to ionize gases. This is the basis for the electron bombardment ion source (see ). A satisfactory electrode arrangement enables the production of a beam of ions much more nearly homogeneous in energy than with the arc, greatly simplifying the ensuing analyzing method. Electron impact has remained the most widely used method of ionization in mass spectrometry. It is subject to problems common to the arc: an almost total lack of selectivity as to the chemical element ionized and, to a lesser extent, the production of ions with degrees of ionization greater than one. Electron impact is utilized extensively in fields of study in which the sample is gaseous or prepared in gaseous form. Isotopic studies of carbon, nitrogen, oxygen, sulfur, and the noble gases make up a large field of endeavour. Electron impact is useful for studying organic compounds. Organic molecules are ionized not only as ions of the whole molecule but in a range of fragments as well. This property, which may at first seem disadvantageous, is actually quite valuable in organic identifications because the resulting mass spectrum allows the identification of the source molecule as uniquely as fingerprints are used in human identification. This forms the basis of a powerful method of organic analysis. If the fragmentation of the molecule is harmful to the objectives of the experiment, another method of ionization can be employed that produces few fragments. In this technique a reagent such as methane (CH4) is mixed with the sample gas and subjected to electron bombardment. The ionized methane (CH) reacts to form CH, which in turn reacts to ionize the sample gas by proton or charge transfer. This process is called chemical ionization, and in some cases it increases the mass of the ion formed by one unit.