Factors of importance for surface analysis
A number of factors impose limitations or introduce complications in surface analyses. The following is not an all-inclusive list but represents the most important factors.
Escape depth
Electrons and ions have finite escape depths from a solid because the probability that they will be scattered before emerging from the surface increases with depth. The escape depth of an ion or an electron varies as a function of its kinetic energy and the angle of emergence from the surface. Because scattering results from interaction of the electron or ion with atoms or molecules in the surface, the higher its energy, the greater the probability that it will penetrate the solid without being scattered. At low energies electron escape depth also increases because at these energies it is possible for the electron to avoid regions of high electron density and thus escape with increasing probability as the electron energy is decreased.
Surface damage
Ideally, any analytical measurement should not change the sample being measured. If the conditions of the measurement or the probe with which the analysis is being done changes or damages the sample, the results of the analysis will be incorrect. For example, if an electron beam used as a probe reduces the species on the surface, the reduced species will be the result of the analysis and not the original oxidized species.
The major source of sample destruction in surface spectroscopy is the probe beam itself. Photons, electrons, and ions all can cause damage to samples, especially when highly focused. In general, photons are least destructive, although the X-rays in XPS can cause some damage to photosensitive materials and sometimes change a material’s oxidation state.
Electrons are more destructive than photons and are more of a problem for insulators than for either semiconductors or conductors. They are especially bad for organic materials. Electron beams can cause sputtering, with the main effect being chemical damage, particularly in AES. Migration of species to or from the surface occurs as well as desorption of adsorbed species under the bombardment of an electron beam. Damage of insulators by electron beams can be quite severe.
Ion beams are the most destructive. The sputtering process induced by ion beams is the source of secondary ions and forms the basis for depth profiling, which is one of the major uses of SIMS. If minimizing sample damage is a priority, it is important to keep the current density low and the sampling time as short as possible. SIMS in the static mode is performed at an ion density of about 10−9 A/cm2 or below. Dynamic measurements, performed at ion densities of 10−6 A/cm2, should be used only if one is willing to allow for surface damage in the course of measurement. RBS can also cause damage, depending on the primary ion dose.
Surface contamination
All real-world samples are contaminated through exposure to the atmosphere. A clean piece of any metal will pick up a contamination layer of carbon when left in the air for an hour. An XPS spectrum of any metal that has been exposed to the air will show a large carbon signal from organic contamination. Easily oxidized materials pick up a film of surface oxides, while moisture in the air can modify some surfaces.
Fortunately, these layers are not thick, and the surface can usually be sampled through the contamination layer. However, it is important to be aware of the existence of the contamination and to recognize that such a layer can affect the intensity of the signal obtained from the surface of interest.
Blooming
Spatial resolution for surface mapping is limited for several techniques by an intrinsic effect, called blooming, that results from scattering of charged particles in solids. When a beam of highly focused, high-energy charged particles such as electrons strikes a solid and penetrates the surface, the paths of the electrons diverge because of optics and electron scattering. The shape of the area affected by the electron beam resembles an inkwell or an inverted light bulb. The depth and therefore the diameter of the affected area are dependent upon the kinetic energy of the particles in the incident beam. Because X-rays are generated throughout the entire volume and will exit the surface of the sample, the smallest unit area in the image will not be that of the diameter of the incident beam but will rather be that of the diameter of the widest part of the inkwell or light bulb. This limits resolution.
Because scattering of electrons also generates noise, blooming also increases the background noise from the sample, which can cause problems with the detection of small quantities, particularly of light elements.
The future of surface analysis
The current trend in surface analysis is toward measuring smaller domains, obtaining more chemical information, and developing techniques that can provide this information without having the sample in a vacuum. Some particularly exciting ideas have been employed in attempts to obtain chemically specific information from atomic force microscopy.
Applications for surface analysis continue to expand. The emergence of nanotechnology has created new demands for surface analytical techniques. As particles become smaller, the surface area per unit mass increases tremendously. For example, a 1-cm cube with a density of 2 grams/cm has a surface area to density ratio of 3 cm2/gram. If that same cube is divided into 1-μm cubes, the ratio increases to 3 metres2/gram. If the original cube is divided into 100-nm cubes, the ratio increases to 3,000 metres2/gram. Thus, the properties of nanoparticles are, in essence, the properties of their surfaces. As the sizes of chips in microelectronics are reduced, surface areas increase for the same reason. Surface analysis is clearly an area in which technological need drives scientific progress.
Shirley Hercules David M. Hercules