Tire materials

intire
print Print
Please select which sections you would like to print:
verifiedCite
While every effort has been made to follow citation style rules, there may be some discrepancies. Please refer to the appropriate style manual or other sources if you have any questions.
Select Citation Style
Share
Share to social media
URL
https://mainten.top/technology/tire
Feedback
Corrections? Updates? Omissions? Let us know if you have suggestions to improve this article (requires login).
Thank you for your feedback

Our editors will review what you’ve submitted and determine whether to revise the article.

Also known as: tyre

News

Tyre marks hint that China’s Fujian aircraft carrier is readying for take-offs Dec. 10, 2024, 8:23 PM ET (South China Morning Post)

A pneumatic tire is reinforced by layers of relatively inextensible cords that hold the air pressure and restrict deformation and growth of the tire during use. To this end cord materials must have high stiffness, resistance to repeated flexing, high strength-to-weight ratio, and good adhesion to rubber. Tire cords have been made of cotton, rayon, nylon, polyester, and glass, but steel and polyaramid (an extremely hard and stiff synthetic fibre) are currently the dominant materials in use.

Various rubber compounds are used in different parts of the tire. The liner, which is intended to minimize the loss of air, is usually made of butyl rubber because that material has a low permeability to gas. Sidewalls, on the other hand, must resist scraping, flexing, and attack by ozone in the air. A typical formulation for sidewalls (measured in parts by weight of each ingredient) would be 50 parts natural rubber (for resistance to heat buildup), 50 parts butadiene rubber (for abrasion resistance), and 50 parts carbon black (for reinforcement), along with small amounts of processing oil, antioxidant, and protective wax. A tire’s treads must be especially resistant to abrasion. A tread compound might have no natural rubber at all but rather 65 parts styrene-butadiene rubber (for hardness and abrasion resistance), 35 parts butadiene rubber, and as much as 65 parts carbon black.

The addition of carbon black or silica as reinforcing agents in rubber compounds has greatly prolonged tire life. Also contributing to longevity are the abrasion-resistant polymer polybutadiene and improved vulcanization systems. (Vulcanization is the interlinking of rubber molecules in order to create a usable elastic solid. It is conducted by heating the rubber mix along with sulfur and various additives in a tire mold for about 20 minutes at a temperature of approximately 300° F, or 150° C.) These advances, together with the almost universal adoption of radial-ply construction (described below), have extended the life expectancy of some tires to more than 90,000 miles (150,000 km). Still, it must be emphasized that the formulation of rubber mixes for tires is more an art than a science. For instance, why a tread recipe based on butadiene rubber will have greater abrasion resistance than one based on natural rubber or styrene-butadiene rubber is not known.

Pneumatic tire structures

The most important feature of tire design is the ply, i.e., the way in which the layers of reinforcing cords in the inner carcass are laid, or arranged. The three main types of arrangements are the bias-ply, the bias-ply belted, and the radial-ply belted. As shown in the illustration, the cords in a bias-ply tire are laid at a “crown” angle of about 50 degrees to the axis of the tire tube, and the cords in successive plies (two or four) cross one another—an arrangement that serves to equalize cord tensions. In a bias-ply belted tire, another set of cords overlies the bias-laid ones. This extra set of cords, called a belt, is typically made of fibreglass. A radial-ply belted tire also has a belt running around the entire tire, but the cords are typically made of steel wire-mesh, hence the term “steel-belted radial” tire.

Belted bias-ply tires have a longer tread life and provide better gasoline mileage than conventional bias-ply tires. They also have better resistance to blowouts and reduce stopping distance in braking. Belted tires supplanted conventional bias-ply tires in the United States in the 1960s and ’70s. Meanwhile, though, radial-ply tires had already become standard equipment in Europe.

In the radial structure, layers of cords are arranged to lie almost perpendicular to the axis of the tire tube. Because the tire is actually a toroid (a circular tube) rather than a straight cylinder, the ply cords actually lie approximately 11 degrees off the perpendicular. This arrangement maximizes the tension across the width of the tire for a given air pressure, and hence gives greater resistance to lateral distortion of the tire on cornering. Radial tires provide better steering characteristics and less rolling resistance than bias-ply tires, tend to run cooler, are safer in bad weather, and are said to give considerably more mileage. They are more expensive than bias-ply tires and have a slightly hard riding quality. Radial tires are now the most widely used type of tire. Bias-ply tires are still widely used in Third World countries, and they are also used for aircraft because they are less susceptible to damage by severe overloads.

Tire specifications

Tires made to North American and European standards carry a code that shows their size and expected performance. In the American “P-metric” system, tire size is indicated, for example, by the code P215/70R15, where the letter P denotes a passenger-vehicle tire; 215 denotes the tire width in millimetres; 70 denotes the aspect ratio, i.e., the ratio of the tire’s height from rim to tread, relative to its width; R denotes radial construction; and 15 is the wheel rim diameter in inches. In addition to size, a speed rating is given using a letter code: S for a maximum speed of 112 miles per hour (180 km/h); T for 118 mph; H for 130 mph; V for 149 mph; and Z for more than 149 mph. A tread wear rating is given for expected tread life as a percentage of that for a standard tire. For example, a rating of 300 would imply a tread life three times as long as that of the reference tire.

Snow tires

Snow tires have an extra-deep tread for better traction on snow and ice. They are reputed to have 50 percent more pulling ability than regular tires on loosely packed snow and nearly 30 percent more on glare ice. In stopping on glare ice, however, snow tires have no advantage over regular tires; tire chains or studded tires are best for ice surfaces. Studded tires usually have about 100 studs tipped with tungsten carbide which contact the road as the tire rotates. Because of the damage they are said to cause road surfaces, they are prohibited in certain localities.